|
As an alternate for reaching in, under, and around obstacles, Ingersoll Rand
Arm Systems allow an operator to precisely and effortlessly position loads
regardless of physical strength. Used in conjunction with an Ingersoll Rand end
effector an operator can perform a wide variety of material handling
applications. The full line of
Ingersoll Rand Zimmerman Arms can handle loads from 150
pounds up to 500
pounds
(68 kg to 227 kg) and offer the most flexibility available on the market today.
 Series 700C
Manipulator Arm
The 700C series arms can be column mounted, ceiling
mounted or carriage mounted. It integrates a balancer to
create a standard arm system that can effortlessly
position loads. The 700C Arm is a “banjo” arm consisting
of three connecting linkages which allows the
boom/balancer combination to cover a large area. The arm
can fold into itself and articulate 270 degrees to reach
around columns, posts or other interference points. The
700C has a short stack-up, which is useful for low
headroom applications because it minimizes interference
with the operator. It has a maximum capacity of 500lbs
and a reach of 10 feet. The balancer is mounted at the
rear of the arm and pulleys in the center section route
the wire rope to the front of the arm. The unit can be
easily fitted with a standard or custom end effector depending on your
application.
 Series 701C
Manipulator Arm
The 701C series arms can be column mounted, ceiling
mounted or carriage mounted. It integrates a balancer to
create a standard arm system that can effortlessly
position loads. The 701C Arm is a “banjo” arm consisting
of three connecting linkages which allows the
boom/balancer combination to cover a large area. The arm
can fold into itself and articulate 270 degrees to reach
around columns, posts or other interference points. The
701C is well suited for lightweight parts and has a
maximum capacity of 150lbs and a reach of 10 feet. The
balancer is mid-mounted and pulleys in the center
section route the wire rope to the front of the arm. The
unit can be easily fitted with a standard or custom end effector depending on your
application.
 Series 713
Manipulator Arm
The 713 arm is very useful in areas with limited
space. It incorporates an over-under boom design with
two linkages and two pivots. One pivot is between the
mounting point and main boom and the other is between
the two booms. Each pivot can rotate 360 degrees, which
allows the operator full coverage of the work area,
including directly under the carriage. It has a maximum
capacity of 500lbs and an 8ft reach. The balancer is
mid-mounted and pulleys in the center section route the
wire rope to the front of the arm. The unit can be
easily fitted with a standard or custom end effector depending on your
application.
 Series 720
Manipulator Arm
Ideal for lightweight parts that require the operator
to work directly under the arm, the 720 arm incorporates
an over-under boom design with two linkages and two
pivots.
One pivot is between the mounting point and main
boom and the other is between the two booms.
Each pivot
can rotate 360 degrees, which allows the operator full
coverage of the work area. It has a maximum capacity of
150lbs and an 10ft reach. The balancer is mounted at the
end of the arm.
The unit can be easily fitted with a standard or custom
end effector depending on your
application.
 Series 600
Manipulator Arm
For loads that can not wobble, and adaptable to most
overhead rail systems, the 600 series arm consists of a
rigid vertical beam with a moving horizontal beam that
is able to reach into an opening. The unit features 360
degree rotation and utilizes BA balancers for lifting
and balancing power. The unit can be used with a variety
of end effector combinations.
Utilizing on overhead arm and parallel link design,
the 400 series arm is an alternative for reaching in,
under and around obstacles. The 400 series parallel link
arm is designed to maintain either end effector or tool
orientation and allows the operator to effortlessly
position a part or tool. The 400 series arms are
typically carriage mounted and adaptable to most
overhead rail systems. The unit can be easily fitted
with a standard or custom end effector depending on your
application.
|
